To reset a Glow-worm boiler, press and hold the reset button on the front control panel for a few seconds, then release it and wait for the boiler to restart. On most models the button is red or marked “reset”. We’re Clever Energy Boilers: Gas Safe registered installers based in Bingley, fitting boilers across Yorkshire and the Humber, the North West and the Midlands. If you’ve got an older Glow-worm that keeps needing a reset, replacing it with a new boiler is the better long-term choice for efficiency and lower repair bills.

We’ve fitted more than 25,000 boilers over 15 years, and Glow-worm is a brand we know well. Glow-worm is part of the Vaillant Group, so many of its fault codes match Vaillant’s. This guide covers where the reset button is, how to reset safely, which codes a reset will clear and when to stop. If you’re weighing up the two brands, our Glow-worm vs Vaillant comparison is a good read.

How do I reset my Glow-worm boiler?

You reset a Glow-worm boiler by pressing and holding the reset button for a few seconds. Some models reset in about three seconds, others need you to hold it for up to ten, so check your user guide if the first try doesn’t work. Before you press it, run through these checks:

  1. Note down the fault code on the display.
  2. Check your gas is on and your prepayment meter has credit.
  3. Look at the pressure gauge. It should sit between 1 and 1.5 bar when the boiler is cold.
  4. In freezing weather, thaw the condensate pipe outside with warm (not boiling) water.
  5. Press and hold the reset button, then release it and give the boiler a few minutes.

Where is the reset button on a Glow-worm boiler?

The reset button on a Glow-worm boiler is on the front control panel, usually near the display or the control knobs. It’s often red, and on some models it carries a flame symbol or the word “reset”. On older Glow-worms with a fold-down flap, it may sit behind the flap.

Glow-worm range Where to look
Glow-worm Energy Front control panel, next to the display
Glow-worm Ultimate Front control panel, next to the display
Glow-worm Betacom and Easicom Front control panel. Check the user guide for your version
Older Glow-worm models (Ultracom, Flexicom, 30ci) Front panel, sometimes behind a fold-down flap

Which Glow-worm fault codes can a reset clear?

A reset clears Glow-worm lockout codes once the cause has been sorted. Glow-worm itself says that in most cases a locking fault will still show after a reset if the cause hasn’t been fixed. Here’s what to do with the codes we see most:

Glow-worm code What it usually means Will a reset help?
F28 The boiler failed to light Yes, after checking gas credit and the condensate pipe
F29 The flame went out during operation Yes, after the same checks as F28
F22 (F9 on older models) Low water pressure Only after topping up the pressure
F75 Pump or pressure sensor fault Try once. If it returns, call an engineer

For anything else, our Glow-worm boiler fault codes guide lists every code.

What does a flashing symbol on my Glow-worm boiler mean?

A flashing symbol on a Glow-worm boiler usually shows the boiler is busy with a particular job, such as heating or hot water, or that it’s waiting before it fires again. On its own that’s normal. If a symbol flashes alongside an F code, the code is what matters, so look it up before you reset.

Why won’t my Glow-worm boiler reset?

A Glow-worm boiler won’t reset when the fault that caused the lockout is still there. No gas, low pressure and a frozen condensate pipe are the three most common reasons. If you’ve ruled all three out and it still locks out straight away, a part inside the boiler has likely failed.

Why does my Glow-worm keep locking out?

A Glow-worm that keeps locking out usually has a part that’s wearing out, such as an ignition electrode, fan or pump. In winter, a condensate pipe that freezes overnight is the most common cause we come across. Repeated resets are a sign of a deeper problem, so stop after two attempts and get a Gas Safe engineer to find the cause.

Is a Glow-worm that keeps locking out a sign you need a new boiler?

A Glow-worm that keeps locking out is often a sign you need a new boiler if it’s more than 8 years old. Older Glow-worm models are less efficient than modern A-rated boilers, and repeat repairs add up fast. A new boiler brings lower gas bills, fewer call-outs and long, market-leading warranties available through us.

Get a new boiler with Clever Energy

We install new boilers across Bradford, Leeds, Huddersfield, Halifax, Wakefield and the wider Yorkshire area, plus the North West and the Midlands. Prices start from £1,999 installed, with fixed online pricing and finance options. See our boiler installation page or get your fixed price online.

Glow-worm reset FAQs

How do I reset a Glow-worm boiler after a power cut?

Most Glow-worm boilers restart by themselves once the power returns. If yours shows a fault code afterwards, press reset once.

Is resetting a Glow-worm the same as turning it off at the wall?

Turning a Glow-worm off at the wall restarts the electronics but doesn’t always clear a lockout. Use the reset button for lockout codes like F28 and F29.

How long should I hold the reset button on a Glow-worm?

Hold it for a few seconds. Some models need up to ten. Your user guide gives the exact time for your boiler.

How many times can I reset my Glow-worm boiler?

Reset no more than twice for the same fault. If the code comes back, a Gas Safe engineer needs to look at it.

More Glow-worm error codes

Good news, we install Boilers in your area!

We offer fast installation slots and a range of finance options.

Get a quote