To reset a Vaillant boiler, press and hold the reset button for about three seconds, then let go and give the boiler a few minutes to restart. The reset button sits on the front control panel near the display and is usually marked with a flame crossed through by a line. We’re Clever Energy Boilers: Gas Safe registered installers based in Bingley, fitting boilers across Yorkshire and the Humber, the North West and the Midlands. If you find yourself resetting an older Vaillant again and again, a new Vaillant boiler is usually the smarter move for long-term efficiency and lower repair bills.

Over 15 years and more than 25,000 installations, we’ve seen just about every Vaillant fault there is. Below you’ll find where the reset button is, how to reset safely, which Vaillant fault codes a reset will clear and which ones it won’t. If you want to look up a specific code, our Vaillant boiler error codes guide has the full list.

How do I reset my Vaillant boiler?

You reset a Vaillant boiler by pressing the reset button once and holding it for around three seconds. Vaillant advises not holding it for more than ten seconds. Before you press it, check the pressure gauge and the gas supply, because a reset won’t fix either of those.

  1. Read the fault code on the display and note it down.
  2. Check the boiler pressure is between 1 and 1.5 bar. Top it up with the filling loop if it’s lower.
  3. Make sure your gas is on and your prepayment meter, if you have one, has credit.
  4. Press and hold the reset button for about three seconds, then release it.
  5. Wait a few minutes while the boiler runs its start-up checks.

Some Vaillant boilers need two attempts before they restart. If it still won’t go after that, stop and look at the code again.

Where is the reset button on a Vaillant boiler?

The reset button on a Vaillant boiler is on the front control panel, close to the display screen. On most ecoTEC models it’s a small button with a flame symbol crossed through by a line. A few older Vaillant boilers use a reset position on a dial instead of a separate button.

Vaillant model Where the reset is
Vaillant ecoTEC plus Reset button on the front panel next to the display
Vaillant ecoTEC pro Reset button on the front panel next to the display
Vaillant ecoFIT pure Reset button on the front panel next to the display
Older Vaillant models (turboMAX and similar) Reset button or dial on the control panel. Check your user manual

If you can’t find it, the user manual tucked behind the front flap or in your boiler paperwork shows the exact layout for your model.

Which Vaillant fault codes can a reset clear?

A reset clears Vaillant lockout faults once the cause has gone, but it won’t fix a pressure problem or a failed part. This table shows what to do before you reach for the button:

Vaillant code What it means Will a reset help?
F28 Ignition failure. The boiler couldn’t light Yes, after checking gas supply and the condensate pipe
F29 Flame loss during operation Yes, after the same checks as F28
F22 Dry fire or low water pressure Only after topping up the pressure
F75 Pump or pressure sensor fault Try once. If it returns, call an engineer
F83 Flow and return temperature problem Try once after checking the pressure
F62 Gas valve shut-off fault No. This needs a Gas Safe engineer

Why won’t my Vaillant boiler reset?

A Vaillant boiler won’t reset when the cause of the fault is still there. The boiler checks itself every time it starts, and if it finds the same problem it locks out again. The usual reasons are no gas, low pressure, a frozen condensate pipe or a part that has failed inside the boiler.

If your boiler shows no fault code at all and still won’t fire, our guide to a Vaillant boiler not working with no fault code goes through the checks.

How many times can I reset a Vaillant boiler?

You should reset a Vaillant boiler no more than twice for the same fault. Vaillant says needing to reset regularly isn’t normal, and pressing the button over and over can make things worse. If the code comes straight back, the boiler is telling you it needs attention.

Why does my Vaillant boiler keep needing a reset?

A Vaillant that keeps needing a reset has a recurring fault, and on older boilers that’s often wear and tear catching up. Ignition electrodes wear down, fans slow, pumps stick and condensate traps clog. Each one can trigger a lockout every few days.

In winter, the most common cause we see is a frozen condensate pipe. If your boiler locks out every cold night, thawing the pipe and having it insulated or rerouted will usually solve it. For everything else, a Gas Safe engineer needs to find the worn part.

Is a Vaillant that keeps locking out a sign you need a new boiler?

A Vaillant that keeps locking out is often a sign you need a new boiler if it’s more than 8 years old. Repairs on older boilers get more expensive and less reliable each year, while a new A-rated Vaillant uses less gas to heat the same home. You also get the reassurance of long, market-leading warranties available through us, so you’re not paying for the next breakdown.

Get a new Vaillant boiler with Clever Energy

We fit Vaillant ecoTEC boilers across Bradford, Leeds, Huddersfield, Halifax, Wakefield and the rest of Yorkshire, plus the North West and the Midlands. New boilers start from £1,999 installed, and you can see your fixed price online before you book anything. Take a look at our Vaillant boiler installation page or get your fixed price online.

Vaillant boiler reset FAQs

How do I reset a Vaillant boiler with no display?

Older Vaillant boilers without a digital display usually have a reset button or a reset position on the control dial. Press or turn it for a few seconds, then wait for the boiler to restart.

Does turning a Vaillant off at the wall reset it?

Turning a Vaillant off at the wall restarts the electronics but doesn’t always clear a lockout. Use the reset button for lockout faults like F28 and F29.

Should I reset my Vaillant after a power cut?

Most Vaillant boilers restart on their own after a power cut. If yours shows a fault code once the power is back, press reset once.

Should I reset the thermostat or the boiler?

Reset the boiler if it shows a fault code. If the boiler looks normal but the heating won’t come on, check the thermostat settings and batteries first. Our guide to a boiler thermostat not working can help.

More Vaillant error codes

Good news, we install Boilers in your area!

We offer fast installation slots and a range of finance options.

Get a quote