How you reset a Baxi boiler depends on the controls. If it has a reset button, press it until the red lockout light goes out. If it has a selector knob, turn it to R (reset) and hold it for at least five seconds before releasing. We’re Clever Energy Boilers: Gas Safe registered installers based in Bingley, fitting boilers across Yorkshire and the Humber, the North West and the Midlands. If your older Baxi keeps locking out, a new Baxi boiler is the better long-term option for efficiency and lower repair bills.

With more than 25,000 installations behind us over 15 years, we’ve seen every type of Baxi control panel there is. This guide shows you how to reset each type, which Baxi fault codes a reset will clear, and when to stop pressing buttons and call an engineer. If your Baxi is gurgling or showing DEAIR, our Baxi boiler deair guide explains what’s happening.

How do I reset my Baxi boiler?

You reset a Baxi boiler using the reset button, the selector knob or the thermostat knob, depending on your model. Check the basics first:

  1. Note the fault code on the display.
  2. Check your gas is on and your prepayment meter has credit.
  3. Check the pressure gauge reads between 1 and 1.5 bar. Top up using the filling loop if it’s low.
  4. If it’s freezing, thaw the condensate pipe outside with warm (not boiling) water.
  5. Reset the boiler using the method for your control panel (see the table below).
  6. Wait a few minutes. The fault code should be replaced by the boiler temperature, and the burner light should come on shortly after.

Where is the reset button on a Baxi boiler?

The reset on a Baxi boiler is on the front control panel, and there are three main types. Baxi’s own guidance sets out each one:

Baxi control type How to reset
Reset button Press the reset button until the red lockout light goes out
ON/OFF/selector knob with an R position Turn the selector to R, hold for at least 5 seconds, then release
Thermostat knob (older models) Turn the knob fully anticlockwise, hold until the red lockout light goes out, then turn it back to your usual setting

The Baxi 400, 600 and 800 series, along with older Duo-tec, Platinum and Combi models, all use one of these methods. Your user guide shows which one your boiler has.

Should I reset a Baxi E133 fault?

You can reset a Baxi E133 fault once you’ve checked the gas supply and condensate pipe. E133 means the boiler couldn’t light, and it’s one of the most common Baxi codes in cold weather. A frozen condensate pipe or an empty gas meter causes most E133 lockouts, and both are safe for you to check. If E133 comes back after a reset, the ignition electrode, gas valve or circuit board needs a Gas Safe engineer. Our Baxi E133 fault guide covers every cause.

What does a flashing light on my Baxi boiler mean?

A red light on a Baxi boiler, whether it’s flashing or steady, means the boiler has locked out. Other lights and symbols vary between models. Some Baxi panels flash green or red in different patterns to show different things, so if you see a flashing light without a fault code, check your user guide for what it means on your model.

Which Baxi fault codes can a reset clear?

A reset clears Baxi lockout faults once the cause has gone. It won’t fix low pressure or a failed part. Here’s a quick guide to the codes we’re asked about most:

Baxi code What it means Will a reset help?
E133 Ignition failure Yes, after checking gas and the condensate pipe
E119 / E118 Low water pressure Only after topping up the pressure
E160 Fan fault Try once. If it returns, call an engineer
E125 Poor water circulation Try once after checking pressure and radiator valves
E110 Overheat Try once. If it returns, call an engineer

Why won’t my Baxi boiler reset?

A Baxi boiler won’t reset when the cause of the lockout is still there, or when it’s been reset too many times. Baxi’s manual for its Heat 600 range says that if five lockouts are reset within an hour, the boiler stops working until an engineer clears it. If you’ve checked the gas, pressure and condensate pipe and it still won’t restart, the fault is inside the boiler.

Is a Baxi that keeps locking out a sign you need a new boiler?

A Baxi that keeps locking out is often a sign you need a new boiler if it’s more than 8 years old. Frequent lockouts point to worn parts, and Baxi itself advises that regular lockouts need an engineer. A new A-rated Baxi uses less gas, runs more reliably and comes with long, market-leading warranties available through us.

Get a new Baxi boiler with Clever Energy

We install Baxi boilers across Bradford, Leeds, Huddersfield, Halifax, Keighley and the rest of Yorkshire and the Humber, as well as the North West and the Midlands. New boilers start from £1,999 installed, with fixed online prices and finance options. Visit our Baxi boiler installation page or get your fixed price online.

Baxi boiler reset FAQs

What’s the difference between a Baxi reset and a deair?

A reset clears a lockout so the boiler can try to light again. A deair is a venting cycle that clears air from the boiler and runs on power-up. They do different jobs.

Should I reset my Baxi after a power cut?

Most Baxi boilers restart by themselves after a power cut, and some run a deair cycle first. If a fault code shows afterwards, reset once.

How many times can I reset a Baxi boiler?

Reset no more than twice for the same fault. Some Baxi boilers stop working after five resets in an hour.

Why isn’t my Baxi reset button working?

If the reset button doesn’t clear the fault, the cause is still there. Check the gas, pressure and condensate pipe, then call a Gas Safe engineer if it still won’t reset.

More Baxi error codes

Good news, we install Boilers in your area!

We offer fast installation slots and a range of finance options.

Get a quote