Baxi Boiler Deair: How to Run a Deair Cycle

Baxi Boiler Deair: How to Run a Deair Cycle

A Baxi boiler deair is an automatic cycle that pushes trapped air out of the boiler and heating system before the burner lights. On the Baxi 800 Combi 2, it starts by itself when the boiler is switched on, shows DEAIR on the display and runs for 6 minutes and 20 seconds. We’re Clever Energy Boilers: Gas Safe registered installers based in Bingley, fitting boilers across Yorkshire and the Humber, the North West and the Midlands. If your older Baxi keeps struggling with air, pressure drops and lockouts, a new Baxi boiler is the better long-term option for efficiency and lower repair bills.

We’ve completed more than 25,000 installations over 15 years, and the deair message is one of the things new Baxi owners ask us about most. This guide explains what the deair does, when it runs, how to start it again and what to do if it keeps repeating. If you’re hearing gurgling from your pipes, our guide to a boiler airlock is worth reading too.

What is a deair on a Baxi boiler?

A deair on a Baxi boiler is a venting phase that clears air from the heat exchanger, the pump and the heating pipework. The boiler runs its pump in short bursts without lighting the burner, so air bubbles can work their way to the automatic air vent and escape. Air in a boiler causes noise, poor heating and lockouts, so the deair protects the boiler before it starts working hard.

When does a Baxi boiler run a deair?

A Baxi 800 Combi 2 runs a deair automatically every time it powers up, including after a power cut. The Baxi manual is clear that if the power drops out, the venting procedure starts again from the beginning. You’ll typically see it:

  • When a new boiler is first switched on.
  • After a power cut or after the boiler has been switched off at the wall.
  • After an engineer has drained and refilled the system.

It’s a sign the boiler is doing exactly what it should.

How do I start a deair cycle on my Baxi boiler?

You can start a deair cycle on a Baxi 800 Combi 2 by switching the boiler off at the fused spur, waiting a few seconds and switching it back on. Because the deair runs on every power-up, a power cycle is the simplest safe way to repeat it at home.

Baxi model How the deair starts What the display shows How long it takes
Baxi 800 Combi 2 Automatically on power-up Dashes, DEAIR and the heating pressure, in turn 6 minutes 20 seconds
Baxi 600 and 400 series Automatically on power-up on most models Varies by model. Check your user guide A few minutes
Older Baxi models (Duo-tec, Platinum) Varies. Some need an engineer to run a purge Varies by model Varies

Before you power cycle the boiler, check the pressure gauge. If it’s below 1 bar, top it up to between 1 and 1.5 bar first, then let the deair run.

Can I use my heating while the Baxi deair is running?

You can’t use your heating or hot water while the Baxi deair is running, because the burner stays off until it finishes. Leave the boiler alone for the full cycle and it will be ready to use as soon as the display goes back to normal. If you turn it off part way through, the deair simply starts again from the beginning next time.

Why does my Baxi boiler keep doing a deair?

A Baxi boiler keeps doing a deair if it keeps losing power or if there’s still a lot of air in the system. A tripping fuse spur, a loose plug or regular power cuts will all restart the cycle. So will air that keeps getting into the system, which usually points to one of these:

  • Low pressure. When the pressure drops, air can be drawn in. Our guide to a boiler losing pressure explains why.
  • Radiators full of air. Cold spots at the top of radiators mean trapped air. Bleed them, then top up the pressure.
  • A sticking automatic air vent. If the vent on the boiler can’t release air, the deair can’t finish the job.
  • A pump problem. A weak or noisy pump won’t push air through the system.

What should I check if the Baxi deair isn’t working?

If the Baxi deair isn’t clearing the air, start with the pressure and your radiators. These are the safe checks:

  1. Top the pressure up to between 1 and 1.5 bar using the filling loop.
  2. Bleed each radiator, starting downstairs and working up.
  3. Check the pressure again and top up if bleeding has dropped it.
  4. Switch the boiler off and on at the spur to run the deair again.

If the boiler still gurgles, loses pressure or shows a low pressure fault code, the air vent, pump or expansion vessel needs a Gas Safe engineer. Our Baxi boiler error codes guide lists the codes to look out for.

Is constant air in a Baxi system a sign you need a new boiler?

Constant air in a Baxi system is often a sign you need a new boiler if it’s over 8 years old and losing pressure regularly. Worn seals, tired pumps and corroded heat exchangers all let air in, and fixing them one at a time adds up quickly. A new Baxi boiler, fitted with a system flush and filter, gives you clean water, steady pressure and lower gas bills. Long, market-leading warranties are available through us too.

Get a new Baxi boiler with Clever Energy

We install Baxi boilers across Bradford, Leeds, Huddersfield, Halifax, Keighley and the rest of Yorkshire and the Humber, as well as the North West and the Midlands. New boilers start from £1,999 installed, with fixed online prices and finance options. Visit our Baxi boiler installation page or get your fixed price online.

Baxi deair FAQs

Should I bleed my radiators before a Baxi deair?

Bleed your radiators if they’re cold at the top, then top up the pressure and let the deair run. The deair clears air from the boiler, and bleeding clears it from the radiators.

Why has my Baxi pressure dropped after a deair?

Pressure often drops slightly after a deair because the air that was vented out leaves a little less in the system. Top it back up to between 1 and 1.5 bar.

Does a deair fix a Baxi low pressure fault?

A deair doesn’t fix low pressure on its own. Top up the pressure first, then let the deair run to clear any air that came in.

Is it safe to stop a Baxi deair halfway?

It’s safe, but the cycle starts again from the beginning the next time the boiler powers up. It’s best to let it finish.

More Baxi error codes

Good news, we install Boilers in your area!

We offer fast installation slots and a range of finance options.

Get a quote