Worcester 2951 Fault Code: What It Means, Causes and Fixes

Worcester 2951 Fault Code: What It Means, Causes and Fixes

A 2951 on a Worcester Bosch display means the boiler has lost its flame too many times and has locked itself out. It isn’t a water pressure fault, whatever some websites say. We’re Clever Energy Boilers: Gas Safe registered (no. 554138), accredited Worcester Bosch installers based in Bingley, fitting boilers across Yorkshire, the North West and the Midlands. If your Worcester is an older one that keeps showing error codes like this, a new Worcester Bosch boiler is usually the better option, both for long-term efficiency and for lower repair bills.

Over the last 15 years we’ve completed more than 25,000 installations, so a locked-out Greenstar is nothing new to us. Below you’ll find what Worcester’s manuals say 2951 means, what usually sits behind it, the checks that are safe to try and when it becomes an engineer’s job. If your boiler won’t light at all, our guide to a boiler not firing up covers the general checks for any make.

What does the Worcester 2951 error code mean?

Worcester’s manuals for the Greenstar 2000 and 4000 describe 2951 as “Loss of flame too many times”. Some versions word it as “Maximum unexpected flame losses exceeded”. In the code tables it’s listed as “2951 V”, which marks it as a locking error.

A locking error stays on the display until the boiler is reset. 2951 doesn’t describe one single fault: it’s raised after a run of flame failures, and Worcester’s remedy is to refer to the blocking errors that led to it and check the fault history. A flame code such as the Worcester 227 fault code is the kind of blocking error an engineer will look for in that history.

You’ll only see 2951 on newer Worcesters with a text display: the Greenstar 2000, 4000 and 8000 Life and Style. Older Greenstar i, Si and CDi boilers show flame faults as a letter and number pair such as EA 227 instead, and our Worcester EA fault code guide covers that older format.

Why is my Worcester showing a 2951 fault?

Anything that keeps putting the flame out can end in a 2951 lockout. These are the usual culprits, most likely first:

  • The condensate pipe or siphon. A blocked or badly routed condensate pipe is the most common cause, especially in winter. Our boiler condensate pipe guide shows how the pipe should run.
  • Gas supply problems. Low or dropping gas pressure, a gas pipe that’s too small for the boiler, or air left in the pipe after gas work.
  • A flue that’s blocked, badly sited or drawing its own exhaust back in.
  • Worn electrodes. Ignition and flame-sensing electrodes wear with age, and their leads can fail too.
  • The PCB. If 2951 returns after a reset and nothing else explains it, look at the control board. Our boiler PCB faults guide explains what that involves.

The condensate pipe and the gas supply are the only ones a homeowner can look at. The rest need a Gas Safe registered engineer.

Is the Worcester 2951 fault dangerous?

The code itself isn’t. It’s a safety response: the boiler couldn’t hold a steady flame, so it shut down and won’t run again until it’s reset.

What’s behind it can be more serious. If you smell gas, open the windows, don’t touch any switches, turn the gas off at the meter and call the National Gas Emergency Service on 0800 111 999. Don’t wait to see whether the code clears.

What can I safely check at home when my Worcester shows 2951?

There are only three checks that are safe for a homeowner, and none of them involve opening the boiler.

  1. Check your other gas appliances. If the hob won’t light either, the problem is the supply rather than the boiler. On a prepayment meter, make sure there’s credit.
  2. Look at the condensate pipe. In cold weather, check the plastic pipe where it runs outside. If it’s frozen, thaw it at ground level with warm water or a hot water bottle, never boiling water, and don’t go up a ladder to reach it. Our guide on how to defrost your condensate pipe walks you through it.
  3. Reset once. On a Greenstar 4000 or 8000 Style, use the arrow keys until “Reset” shows. On a 2000 or 8000 Life, follow the reset steps in your user manual.

Topping up the pressure won’t clear a 2951, because it isn’t a pressure code. If the gauge does read low, that’s a separate problem, and our guide to what your boiler pressure should be explains the numbers.

When should I stop resetting the 2951 error and get a Gas Safe engineer?

If 2951 comes back after one reset, stop pressing the button. Each reset just tries to light the boiler through the same fault. A Gas Safe registered engineer will read the fault history to find the blocking errors behind the lockout, then check the gas pressure at the boiler, the siphon and the flue. Electrode, gas valve and PCB work is for them only. Never take the casing off yourself.

Why does the Worcester 2951 fault code keep coming back?

Because a reset clears the lockout, not the cause. A part-blocked siphon, worn electrodes or gas pressure that keeps dropping will go on putting the flame out until the boiler reaches its limit again.

Frozen condensate pipes are a big reason 2951 turns up in winter across Bradford, Keighley and Halifax. On an older boiler, one call-out tends to lead to another.

Is a 2951 error a sign you need a new Worcester Bosch boiler?

Not always. On a young boiler it might be a frozen condensate pipe and nothing more. On an older one it usually means the condensate route, the electrodes or the gas valve are wearing out together, which is a pattern of repeat call-outs rather than one repair.

These are typical UK prices for the repairs behind a 2951, as a guide only:

Repair Typical UK cost
Electrode or ignition parts £120 to £250
Gas valve £150 to £250
PCB (control board) £250 to £500 for parts, before labour
Engineer labour £60 to £100 an hour

Replacement starts to make more sense if:

  • Your Worcester is over 8 years old, as boilers past that age become noticeably less efficient
  • 2951 or another flame code has come back more than once
  • An engineer has quoted for a new PCB or gas valve
  • You’ve already paid for electrode or condensate work in the last year

Our guide to how much a new boiler costs sets out the prices, and how to know when your boiler needs replacing covers the other warning signs.

Get a new Worcester Bosch boiler with Clever Energy

We install Worcester Bosch boilers in Bingley, Bradford, Leeds, Keighley, Halifax and across Yorkshire, plus the North West and the Midlands. As accredited installers we’ll match the right model to your home and handle the registration for you, and a long, market-leading warranty is available through Clever Energy. Take a look at our Worcester Bosch boiler installation service, get a fixed price online in a few minutes, or request a callback. If you’d rather talk it through, call 0330 055 2210 between 8am and 8pm on weekdays or 10am to 4pm at weekends.

Worcester 2951 fault code FAQs

Why does my Worcester keep showing 2951 after a reset?

Because the reset clears the lockout, not the cause. Something is still putting the flame out, and an engineer needs to read the fault history to find it.

Can a frozen condensate pipe cause a Worcester 2951 fault?

Yes, and it’s one of the most common causes in winter. Thaw the pipe at ground level with warm water, not boiling, then reset the boiler once.

Is the Worcester 2951 code a water pressure fault?

No. Several websites say it is, but Worcester’s Greenstar 2000 and 4000 manuals describe it as loss of flame too many times.

What’s the difference between Worcester 227 and 2951 error codes?

227 is a blocking error for a flame that wasn’t detected. 2951 is the locking error that follows when flame losses keep happening, so a 227 in the fault history often explains the lockout.

Is a Worcester 2951 fault covered under warranty?

It depends on your boiler’s age and the cover you have, so check your paperwork. If you replace it instead, a new Worcester fitted by us comes with access to a long warranty.

More Worcester Bosch error codes

2951 sits at the end of the flame fault family. Before this one, have a look at the Worcester Bosch 229 fault code, where the flame is lost partway through a cycle; after it, the Worcester Bosch D5 fault code covers condensate that isn’t draining. The full list sits on our Worcester boiler error codes guide.

Good news, we install Boilers in your area!

We offer fast installation slots and a range of finance options.

Get a quote